Andromix issue

Pdiddy

Pdiddy

New member
Oct 24, 2017
10
0
Has anyone used Andromix from Geneza? I have had good and bad luck with it. It is a 50/50/50 test prop, tren ace, masteron. I have had success with it but damn some injections just burn and then swell up my injection spot and hurt and swell up for a week, this is the only mix that has done this all my other gear is smooth! Any suggestions? Or has anyone else had this? And is there a way to fix it? Like add more carrier oil and inject more? Is it too much BA? Any help or insight appreciated
 
Steroidify Below First Post
Riff Vibes
Advertise on Hardcore
That may be one way to ease the burn a little....cutting it with some sterile oil. Others way could be massaging the site post injection or you could possibly try heating the oil prior to injection.
 
Thanks for reply, I will try both. What was weird is some vials were great and others hurt worse and they were different batches and I wonder if it is the ba%, thanks a lot I’ll follow up tonight because it’s a daily damn injection lol
 
Warmed up the Andromix yesterday and injected in left pec then tonight warmed up pinned right pec, so far so good! Thanks for the heads up!
 
That's good advice. I always warm up my gear first and rarely have any pip issues, not to mention the oil flows faster into the syringe. I haven't used that Andromix yet but isn't test prop known for usually having some bite to it?
 
BigOiron said:
How do you fellas warm it and how hot?
Click to expand...

I use a hair dryer. You could place them on an electric skillet or stove top burner on low heat for a few minutes giving them a swirl every now then while heating. As far as a specific temperature, I don't know.
 
AlI I do is draw into barrel, I have an empty "cosmetic" container of some sort, in which the opening is small enuff to not let the pin "plunger" end {the wings} on plunger, so replace the needle cap, drop it needle end first into hot tap water in the container, the "wings" hold it in place, nearly the whole barrel is submerged up to the wings. While I towel off from my shower , it's in the warm water for maybe 2 min.

Pull out, grab pin lid with my teeth, (I always bite down on the pin lid while injecting.)

Whalla...! Easy peasy..

MotorCity
 
MotorCityMuscleMachine said:
AlI I do is draw into barrel, I have an empty "cosmetic" container of some sort, in which the opening is small enuff to not let the pin "plunger" end {the wings} on plunger, so replace the needle cap, drop it needle end first into hot tap water in the container, the "wings" hold it in place, nearly the whole barrel is submerged up to the wings. While I towel off from my shower , it's in the warm water for maybe 2 min.

Pull out, grab pin lid with my teeth, (I always bite down on the pin lid while injecting.)

Whalla...! Easy peasy..

MotorCity
Click to expand...

Sounds like contamination could happen easily that way.
 
Advertise on Musclemecca
aasdirect
I put mine on the stove on medium or almost medium heat till the bottle is hot to the touch. Hot enough to be held with oven mitts. Shake it up a bit and then let it settle, not too long though, don't want it to cool down. Then do your draw and inject. Most oil is pretty thick, so the outside of the vial should be hot. If it's just slightly warm I doubt the heat has transferred to the oil. Maybe a little bit but not enough to make the actual oil warm.
 
Kins said:
Yeah, but tap water isn't.
Click to expand...

K, so explain me this then..! (Think first..!) If the lid is on the dart end. And pointing face down into the "very" hot tap water, (and no pressure, cuz it's at rest) full of oil , not even "negative" psi which would be a vacuum.

How it going g to infiltrate the pin..?

Also, the other end had s rubber stopper capable of X amount PSI,. I dont know what psi it may be,. But when we plunge (Inj.) That psi is some formula x the diameter, and barrel length something substantial I'm sure to be able to get the full pin of oil thru a tiny orifice ( the dart ).

So,. With lid on, as I explained. (Also mind you, this is the same tap water I shower with, and have for the 16 years I've been there)

How then, is there "any" contamination..! That's all I ask.

And , again I've been doing this this way for many a year.

Also, might add, in my nearly 16 year's of juicing, I have
"Only" had two ( 2 ) bad Injects, that knotted up, and probably because of the gear. Mex gear mind you, I was t to say Loeffler.., or. One of those.

Zero infections, and zero abscess'

OK, I'm done....!
 
Last edited:
BigOiron said:
How do you fellas warm it and how hot?
Click to expand...

I like to microwave some water for 2 minutes then throw my vial in there for about 5 minutes right before I pin. Oil is usually perfect temp and it takes minimal effort
 
Yates84 said:
I like to microwave some water for 2 minutes then throw my vial in there for about 5 minutes right before I pin. Oil is usually perfect temp and it takes minimal effort
Click to expand...

That's another good option, thx for that. I sometimes nuke coffee if still.a bit in the pot from earlier, lol..., But some good hit nuked tap water would do fine also, unless I trip coming up the stairs with it to do my business, lol...!
And burn my shit..Lol.. Getting old.

Hey, or I could.put the microwave in my room.

MotorCity
 
Yates84 said:
I like to microwave some water for 2 minutes then throw my vial in there for about 5 minutes right before I pin. Oil is usually perfect temp and it takes minimal effort
Click to expand...

Best advice, I was having some pain with test sust and this made in painless each time. Would be sore with minor pip but nothing compared to being in pain for a week plus prior


Sent from my iPhone using Tapatalk
 

Similar threads

xxplosive
PCT Issue
Replies
5
Views
472
xxplosive
xxplosive
OHBRUTUSIO
Joints issue
Replies
13
Views
86
OHBRUTUSIO
OHBRUTUSIO
J
Libido issue
2
Replies
21
Views
137
Argon Coagulator
Argon Coagulator
Back
Top